The Fahraeus effect

doi:10.1016/0026-2862(71)90002-1

Microvascular Research

Volume 3, Issue 1, January 1971, Pages 6-16

https://doi.org/10.1016/0026-2862(71)90002-1 Get rights and content

Abstract

Fahraeus reported in 1929 that when blood flows from a large diameter tube through a capillary tube, the average hematocrit of the capillary blood is less than that of the blood in the larger tube. We have investigated this Fahraeus effect by pumping human blood, and red cell-isotonic saline suspensions, from a large reservoir through capillaries 29–221 μ in diameter. The independent variables were the flow rate, the feed reservoir hematocrit (H_F), the capillary diameter, the stirring rate in the reservoir, and the continuous phase protein content. The measured dependent variables were the average hematocrit in the capillary tube (H_T), and the mixing-cup hematocrit of the blood flowing from the tube.

Under steady flow conditions in the range of conditions studied, the tube relative hematocrit (defined as $H_{R} = H_{T} H_{F}$ ) was found to be independent of the blood flow rate, the protein content of the continuous phase of the red cell suspension, and the stirring rate in the reservoir. H_R is a linear function of H_F for a given capillary size; the straight line representing this function has a slope which increases, and an intercept which decreases as the tube diameter decreases. The mixing-cup hematocrit of the blood flowing from tubes 59μ in diameter or larger was always equal to the feed reservoir blood hematocrit. Unsteady flows result in H_R values which differ from steady flow values. Our results agree with those of Fahraeus (H_F = 40%), but differ from those of Hochmuth and Davis for smaller capillaries.

Besides providing quantitative data, our results support the contentions that flow conditions upstream from the capillary entrance are not responsible for the Fahraeus effect, and that the hematocrit in the capillary is a function of radial position. In 29-μ tubes, we have also observed an axial variation in hematocrit.

References (10)

J.H. Barbee
Internal report: chemical engineering laboratories
(1967)
S. Chien et al.
Plasma trapping in hematocrit determination
R. Fahraeus
The suspension stability of blood
Physiol. Rev.
(1929)
R. Fahraeus et al.
The viscosity of the blood in narrow capillary tubes
Amer. J. Physiol.
(1931)
R.M. Hochmuth et al.
Changes in hematocrit for blood flow in narrow tubes
Bibl. Anat.
(1968)

There are more references available in the full text version of this article.

Cited by (210)

A theoretical model for the Fåhræus effect in medium–large microvessels
2023, Journal of Theoretical Biology
Citation Excerpt :
We had to wait until 1965 when other sets of data appeared, (Palmer, 1965, 1968) and 1968 for the paper by Hochmuth and Davis (1968). Barbee and Cokelet (1971) were the first to use the term Fåhræus effect, (called F effect from now on). In that article, new data were presented together with a complete discussion over all previous data available at that time and over the experimental procedure itself.
This paper presents a mathematical model capable to reproduce a celebrated phenomenon in blood microcirculation known as Fåhræus effect, since its discovery by Robin Fåhræus (1929). This consists in a decaying of the relative hematocrit in small vessels as the vessel diameter decreases. The key point of the model is a formula, direct consequence of the basic principles of fluid dynamics, that links the relative hematocrit to the reservoir hematocrit and the vessel diameter, which confirms the observed behavior. To test the model we selected, among the few experiments carried on since then, those performed by Barbee and Cokelet (1971). The agreement is remarkable. An extended comparison is also carried out with a celebrated empirical formula proposed by Pries et al. (1992) to describe the same phenomenon.
Shear-induced migration of a viscous drop in a viscoelastic liquid near a wall at high viscosity ratio: Reverse migration
2022, Journal of Non-Newtonian Fluid Mechanics
Wall-induced migration of a viscous drop in a viscoelastic fluid subjected to a plane shear is numerically simulated to investigate the effects of drop/matrix viscosity ratio. In a Newtonian system, drop migration away from the wall is inhibited as the viscosity ratio is increased. Here, we show that the introduction of the matrix viscoelasticity further decreases the migration and can even reverse its direction ‘from away’ to ‘towards the wall’, a phenomenon not seen in Newtonian systems. The migration towards or away from the wall eventually settles in a quasi-steady state that only depends on the instantaneous wall separation independent of the initial position of the drop. Drops migrating towards the wall initially increase their velocity, but as they approach the wall, they decelerate, showing a non-monotonic variation. The migration direction depends on the viscosity ratio, viscoelasticity (Deborah number), and the capillary number. We compute phase diagrams in the parameter space showing boundaries where migration changes direction. The critical Deborah number (at a fixed viscosity ratio) and the critical viscosity ratio (at a fixed Deborah number) for direction reversal approximately scales with the inverse of the capillary number.
Moving least-squares aided finite element method (MLS-FEM): A powerful means to consider simultaneously velocity and pressure discontinuities of multi-phase flow fields
2022, Computers and Fluids
Citation Excerpt :
The study of two-phase flow problems provides us with principal knowledge on several industrial and real-life applications, which comprises at least two different components. To give some examples, we can name the followings: the improvement of the heat and mass transfer (e.g., emulsion systems) [2–5], the enhancement of the mixing quality (e.g., in mixing devices) [6–8], the prediction of the second-phase deformation extent (e.g., morphology development in polymer blends) [7,9], the evaluation of the rheological behavior of complex fluids (e.g., blood) [10,11] and many other items [12], such as the drop formation in microfluidic devices [13,14]. In most of the mentioned applications, each component in the flow domain (the major and the minor phases) can have different properties, such as viscosity.
We suggest a strategy to consider discontinuities in the two-phase flow calculations. Our approach comprises enhancing the shape functions of the finite element method (FEM) with the moving least-squares (MLS) interpolation functions. The new shape functions correlate a parameter at any arbitrary point to its surrounding nodes instead of an element's nodes. We name this strategy the "moving least-squares" aided "finite element method" (MLS-FEM).
In a previous paper Mostafaiyan et al., we have employed the concept of the MLS-FEM to develop the PMLS (pressure shape function enhanced by the MLS interpolation functions) method, which predicts pressure discontinuities due to the surface tension forces. We take another additional step to consider velocity and pressure discontinuities in a domain with two different fluids. Therefore, we use the MLS technique to enhance the pressure (P) and velocity (V) shape functions. We name this scheme PVMLS (pressure and velocity shape functions enhanced by the MLS technique).
We validate the PVMLS method with a stationary drop problem (as a benchmark). We show that the previous PMLS method fails to predict an accurate pressure or smooth streamlines by increasing the Capillary number and deviating from the unit viscosity ratio. However, the PVMLS method provides more accurate results since it considers velocity as a discontinuous parameter. Also, we compare the results of the PVMLS method at very high viscosity ratios (undeformable fluid) with a boundary-fitted single-phase problem. The reported similarities between the predicted pressure values and streamlines in both strategies demonstrate the reliability of the PVMLS method. Finally, we discuss that by employing the PVMLS method to calculate the velocity field, the interface advection will be more mass-conservative.
Modeling sphere dynamics in blood vessels for SIRT pre-planning – To fathom the potential and limitations
2019, Zeitschrift fur Medizinische Physik
For selective internal radiation therapy (SIRT) the calculation of the 3D distribution of spheres based on individual blood flow properties is still an open and relevant research question. The purpose of this work is to develop and analyze a new treatment planning method for SIRT to calculate the absorbed dose distribution. For this intention, flow dynamics of the SIRT-spheres inside the blood vessels was simulated. The challenge is treatment planning solely using high-resolution imaging data available before treatment. The resolution required to reliably predict the sphere distribution and hence the dose was investigated. For this purpose, arteries of the liver were segmented from a contrast-enhanced angiographic CT. Due to the limited resolution of the given CT, smaller vessels were generated via a vessel model. A combined 1D/3D-flow simulation model was implemented to simulate the final 3D distribution of spheres and dose. Results were evaluated against experimental data from ${}^{90}Y$ -PET. Analysis showed that the resolution of the vessels within the angiographic CT of about 0.5 mm should be improved to a limit of about 150 μm to reach a reliable prediction.
Two-phase analysis of blood flow through a stenosed artery with the effects of chemical reaction and radiation
2024, Ricerche di Matematica
Microdevice for Plasma Separation and in Vitro Quantification of Plasma Proteins
2024, Lecture Notes in Mechanical Engineering

View all citing articles on Scopus

View full text

The Fahraeus effect

Abstract

Internal report: chemical engineering laboratories

Plasma trapping in hematocrit determination

The suspension stability of blood

Physiol. Rev.

The viscosity of the blood in narrow capillary tubes

Amer. J. Physiol.

Changes in hematocrit for blood flow in narrow tubes

Bibl. Anat.